How To Stain Butcher Block Desk

Let sit for at least 2 hours or according to the brands instructions. ***find an update on sealing butcher block here, after i lived with it for four years*** while the actual title of this post is “how to stain and seal butcher block counters,” an alternate title could be “how not to stain and seal butcher block counters.” because i definitely, definitely did both.

7ft x 2ft butcher block desktop. 2 coats of minwax stain

(i chose to not oil the bottom side of the desk since it was never going to be seen.) step 2:

How to stain butcher block desk. Carefully measure that each of them are in the exact spot. So dry fit first, then take it back off to stain/sand/stain if you like, though not necessary especially if you don’t have the room. How to make inexpensive faux butcher block countertops for a built in desk:

On my journey to find their pre made butcher block tops, i came across something on the entirely opposite end of the store. Bring the butcher block inside and set it upside down. Plan & measure your space.

Live edge means the characteristics of the outside of the tree are on the edge of the butcher block and will go in and out up to a half of an inch. Use the sponge, and scrub the countertop using mild dish soap rinsed in hot water. You may have noticed that the shorter side of the desk only has three legs and thought to yourself “that’s definitely going to fall over!”

Lay the top side facing down and measure where you want to place the 4 legs. Applying product to the bottom of the butcher block will help ward off warping and cracking. Poly (or any varnish) will enhance the color natural/raw wood, as you can see below with the bottom side of the desk.

Apply first coat of finish and wipe off excess. Wipe down your surface with a dry rag to remove anything left over from sanding. So imo butcher block should never be sealed it is one of the easiest materials to look after there is an enzyme in the wood that kills bacteria but if you seal it that does not work i have had butcher block for years i oil it when it looks dry, i sand it lightly if it gets stain or burn then oil it the one in this pic is now about 16 yrs old and still looks like new i just oiled it more often near the sinki also don’t like them.

It’s important to seal the surface of the butcher block completely (top, bottom and sides) to prevent bowing/warping from moisture absorption (i. Here’s a step by step guide to a diy butcher block desk: This helps avoid going too dark in one pass, and reduces blotchiness to some degree.

Apply first coat of polyurethane and allow to dry for 24 hours. Give me some feedback if this is incorrect. So for those.read more »

Now i recommend this for any butcher block, particularly if it is not maple. Most desks are 6’x2.5’ (72”x30”) but choose the size that works best for you up to 39 inches wide without having to join two pieces of butcher block! See more ideas about kitchen remodel, kitchen design, new kitchen.

Also stain your butcher block if you've had your counters for several years and the current finish is looking worn or faded. If you stain first then cut, the fresh cuts will require stain causing a possible line where the new stain covers the previous stain. It’s finally time to start putting it all together!

Apply mineral spirits to the top and allow to dry. Allow to dry over 24 hours. Start by scraping off any food residue using a metal scraper, running it gently on areas with visible food gunk.

Alternatively, you might try using a dye product, either directly on the wood, or as a tint in the clear coat. We applied one coat of minwax stain in dark walnut, and then we sealed the wood with a satin polyurethane. The secret to the inexpensive butcher block top on this built in desk was a specific piece of wooden board i found when i was at lowes.

Then spray undiluted white vinegar, allow it to sit for a few minutes, then wipe it off with a. I didn’t bother wiping off the excess since unfinished block will soak up a lot. Apply next coat if desired, etc.

Sand the wood before staining, then select a wood stain and apply at least 2 coats. Apply a thick layer of butcher block conditioner with either a rag or a brush. Choose your wood species and finish.

So the butcher block is resting on that “lip” and the two drawer units on each side. You will use much less mineral oil and feel more secure knowing juice cannot sink deep into the wood grain when you haven't kept up with the oiling. It’s done in just 5 steps —.

He also used a few screws and attached the butcher block to the drawer unit from underneath to keep it from slipping. Use a generous amount of finishing product on the underside. For a desk, skip the oil after the salad bowl finish dries.

DIY dining table; stained butcher block with a metal base