How To Remove Hardwood Floor Staples

However, sometimes the staples will snap in two and must be pulled out with pliers. Use the vice grips, nail claw and hammer to pull out staples and nails left in the floor.

Sanding and refinished hardwood floors, after removing

Use the hammer to lightly tap the pry bar or flathead screwdriver under the tack strips, then lift them and pry them off with either the pry bar or hammer.

How to remove hardwood floor staples. To replace hardwood floor, start by cutting and prying up the old hardwood planks using a circular saw, pry bar, and mallet. By holding the pry bar teeth flat on the floor and with a slight twisting motion, back and forth, not up and down, you can work the tip of the beveled tooth under the staple. I found the best technique was to grab one end of the staple with a needlenose plier, and twist it so you were pulling each side individually.

So cutting them into smaller pieces of wood, makes it easier to pry up. Cut the pad into strips and roll it up just as you did with the carpet. The original floor was untouched by the staples as they weren't that deep.

A quick jerk in the middle of the staple with the utility knife usually quickly removes the staple in one piece. Once you have gotten all the hardwood floor up, you will notice that in between all the dust, wood and dirt are a bunch of metal staples and nails! To remove them, use a floor scraper.

It’s amazing how many staples or nails a wood floor can hold. The problem is when removing a wood floor. Okay, so the fastest way to remove old hardwood floors is to cut the boards into smaller sections.

The staple will start to pull up and will bend a bit as it comes up. If they are near flush you may need to get under them with something akin to a pointed ice pick just. The floor looks like yours under all that plywood we removed.

How to remove staples from hardwood floors! Use the large magnet to pick them all up. In many cases both ends of the staple will be raised.

A few friends, a few pairs of needle nose pliers, a case of beer, some good music and lots of patience. Layout of the removal area How to remove hardwood flooring first, set the blade depth on your circular saw.

How to remove glued down hardwood floors: Although many nails and staples can be removed with your nail puller, some nails and staples may be broken, and vice grips will allow you to grab ahold of the broken nails and staples to remove them. Then, remove any nails and staples in the subflooring, and sand off any paint or adhesive.

How to remove glued down hardwood floors: My husband and son and the workers had no trouble. It’s a pretty simple process.

I hope you will try to get it off. Our flooring is about 3/4 inches thick, so i set the blade depth about 3/4 inches deep, so that the blade cut through the hardwood floors, without cutting into the plywood subfloor. Then the staples which were affixing the linoleum to the subfloor dug into the hardwood and some broke off when i was pulling them.

It depends how far into the wood the staples are. With all the boards removed, it’s time to remove the nails and staples. It is much quicker doing this and you are making sure the vacuum cleaner is not going to get damaged as a result of nails and staples.

Next, buy replacement flooring, and let it acclimate in the room for 3 days so it doesn't shrink or expand after you install it. Sometimes, one end of the staple may still be stuck in the wood. Depending on the material and the staple used, i have found that most staples will come right out when using the hook blade.

Lastly, if you want to make your hardwood floor removal faster and easier, we suggest having a circular saw on hand. Then, carefully remove staples and nails from the wood. Screwdrivers can be used in the same manner, only take care on finished or delicate woodworking to avoid damaging the wood.

Without exaggerating, a wood floor needs about 8,000 staples (depending on the length, of course). Press down the handle to pop the staple out of the wood. In other cases, only the end of the staple where the tooth had penetrated will pull free of.

This is helpful because hardwood planks are all different lengths and make it really tough to remove quickly. My kids have been hammering the staple stubs in further but i would like to remove them. Pocket knives are used all the time by woodworkers to remove staples.

Call a local floor refinisher and find out what the tool is. Keep one handy, and when you need to, slip the sharp point under the staple and pop it out. Click to see full answer.

Remove the carpet and then gently rip off the carpet padding to reveal the staples used to keep the padding in place on your hardwood floors. When you've torn off all the carpet and pad, pull out all the staples with pliers. Next, remove all carpet, tack strip, carpet pad and especially the carpet staples (sanding over metal creates a spark hazard, and it can destroy the rubber drum or disc plate of a sander).

On a concrete floor, the pad is glued in place, so big chunks of pad will remain stuck to the floor. Some nails may need to be hammered free; It is true that the tongue and groove system makes things easier, but it is always good to be sure of its stability.

Use the vise grips to rip staples and nails out of the floor. Once locked on, just tip the pliers to the side and follow the curve of the tool, slowly rolling the tool on the floor and letting it do all the work of prying the staple out. Protective goggles or work glasses;

In that case, use the pliers to fully remove the staple from the floor.

Pin on Home