How To Replace Bathroom Fan Timer Switch

The blacks on each switch that are seperate, go out to the actual devices, light and fan. Simple 2 core and earth is all that would be required throughout.

Howto Install a Dimmer or Light Switch Light dimmer

Make sure the power is off before you touch any wires in the box.

How to replace bathroom fan timer switch. If it’s a typical small one speed bathroom fan you can use any on/off switch that matches the load specs; The control replaces a normal bathroom switch to provide simple programming. While it may appear messy with the old wallplate cover removed, this is a pretty clean electrical box (it better be in a new home!):

The black wire that was connected to the other side of the existing bath fan switch needs to be spliced to the blue wire from the timer switch. The real beauty of having a bathroom fan timer is that the exhaust fan can be turned on during the shower, and left running after the shower to clear the room of moisture. For the new switch, black to the hot (the group connected together), red to the black going to the fan, and white with the other whites (will replace the old white from old switch).

Post by tommyle » sun feb 12, 2017 9:32 pm. This wire, black from cable 5, connects to load/red on the new switch. The wall switch timer is ideal to control ventilation fan, ceiling fan and light in bathroom and laundry room where light and fan could be left on for a long time.

It is nicely labelled with all 4 connections required for the ge switch (load, line, neutral and ground). To save on your electrical bills we can even install a timer switch for your bathroom exhaust fan so it will run for a set period of time while you shower and a few minutes after to remove the excess humidity and then it shuts itself off so you don’t forget and leave. Typical wiring for exhaust fan switches with two switch wires and a ground wire:

We suggest using the timer on your phone to check this. All of the white neutrals and grounds are connected inside the box, i didn't mess with that, it should have been a simple switch replacement. Go and put the kettle on.

Blue to black switch leg splice. Ground/green should be connected together with all. Remove the old wallplate cover.

The hot wire of fan will go into switch’s black wire. Here, we will be using 3 core and earth. By simply pushing the button to set your desired time delay from 1min, 5min, 10min, 15min and 30 minutes, your appliance will automatically turn off and never be inadvertently left on.

Replacing a standard bath fan with a fan timer switch is an easy solution to leaving your bathroom fan running all day. Is it possible to run t&e from a fused connecter outside the bathroom to the switch then. Sometimes a unit may have different colors used for wires.

This allows you to manually turn the exhaust fan off and on or to program it to run at certain times of the day for increased energy efficiency and convenience. Black wire on bottom of old switch is switched hot. This is a problem that can be easily resolved by replacing the wall fan switch with an automatic timer.

Similarly, you need to take the light’s hot wire for switch’s red wire. The wiring of the bathroom exhaust fan switch will depend on the exact switch that is selected, however below is a description of the most common control switches and how they are wired. With this in mind, if your fan does not have a timer you will not need to use 3 core cable to connect it;

Switch the lights off, and then set the timer on your phone to 14 minutes. There is an exhaust fan timer switch out there called smartexhaust that can replace both your light and fan switch, which allows you to control your exhaust fan and set a delay timer. There are 4 sets of 14/2 wire coming in to the switch box in the bathroom.

I flipped the breaker for my bathroom circuits and pulled the fan switch out. If playback doesn't begin shortly, try restarting your device. I have identified and marked the four black wires coming in to the box as 1) the lead to the fan, 2) the lead to the light, 3.

Just don’t use a dimmer switch intended for lights. Then grounds all get connected together. Replace your bathroom fan switch follow the instructions included with the dewstop switch.

19 20% coupon applied at checkout save 20% with coupon The delay timer will keep the fan running after the switch is turned off to give you more ventilation time when exiting the bathroom, and will shut off automatically after a set time that is programmed (example: Black wire from the new timer device connected.

Both leviton and ge make these. This is for putting the fan and light on different switches. Bathroom exhaust fan timer switches.

When the phone alarm goes off, return to the bathroom and check that the fan is still running for another 60 seconds! I’m worried there is some current flowing through one. Same with the whites, all the neutrals connected together.

Cable types required for the timer fan above are 2 core (twin) and earth. But the display on the dumb switch remains on. The first step for installing the new bathroom fan timer switch is to remove the old ones.

Honeywell Home 7Day Programmable Timer Switch for Lights