How To Adjust Coilovers Without Spanner Wrench

Is it possibe to adjust rear shocks without a spanner wrench? I have to tilt the wrench down and make sure the wrench is grabbing a notch.

Pin on Floor lamp ideas

I've got a 12 so at full droop the spring has no pressure on it and it's easy to move.

How to adjust coilovers without spanner wrench. Go purchase a strap wrench from your local hardware store! I just spend 3 hours reading over past threads and finally decided to post a new one. The wrench has a compact, low profile design that makes it easy to use in the tight clearances of your trucks wheel wells.

By lowering the locking collar (c ) and spring perch (b) the suspension is allowed to compress. This sale is for a full set of 6 spanner wrench. Remember to check the top 17mm mounting nut on the strut shaft as it can come loose during this adjustment.

Kei project universal coilover adjustment spanner wrench tool set fits most coilovers shocks moebulb coilover adjustment tool 4x steel spanner wrench compatible with tein kw ohlins hks apexi cusco jegs universal spanner wrench | removable teeth | billet aluminum | uses 3/8 inch ratchet/breaker bar | includes 2 wrenches After your adjustments are made, tighten the spring perch and locking collar together using the spanner wrenches. You start by loosening up the lower collar with a spanner wrench before adjusting the upper adjustment collar with another spanner wrench.

Does the trick and no scratching (if you're concerned about that). Once you’ve lowered or raised your vehicle to the desired height, hold the top adjustment collar tight as you tighten the lower adjustment collar against it. A vice to hold the shock body is nice too, but you'd.

After your adjustments are made, tighten the spring perch and locking collar together using the spanner wrenches. Take the wheel off and it just takes patience. Return this item for free.

June 05, 2012, 03:53:57 pm » you can also use needle nose vise grips and get those right into the notches. This will result in a lower ride height. I need to adjust them a bit higher for say an 1.

While it work on many coilovers we have tested it may not work on every single coilovers out there so please take look at the picture compare to the coilovers you have and decide wheather it will work or not. This is moving the entire assembly lower by screwing the shock body deeper into them bottom mounting cup and is the proper way to lower/adjust ride height. For vehicles without and adjustable lower mount, use the spring perch to adjust ride height.

It may depend on what size spring you have though. Dont forget the hammer to pound on the screwdriver. If you've got a longer spring that puts pressure on the mount.

This can be done while the coilovers are installed on the car. 4.5 out of 5 stars. I sprayed some wd40 around the collars and threads and used my strap wrench to slowly but easily turn the coils down to my desired height.

Once loose, spin collar b by hand down the length of the coilover. By lowering the locking collar (c ) and spring perch (b) the suspension is allowed to compress. Also tho, you may need to remove tension from the spring to adjust by hand till it's even accessible wth the spanner wrench

With the spanner wrench positioned like so, spin the wrench in the direction indicated by the red arrow in the above photo. You don't need the special wrench.just use a large flatblade screwdriver. Set, if you can't adjust your coilovers with this set, there is.

400925986424[sr] thick usa steel spanner tool wrench wrenches coilover adjustment (set of 6) [sr] thick usa steel spanner tool wrench wrenches coilover adjustment (set of 6) $39.95. This will result in a lower ride height. You'll kinda have to figure it out in your own really without being there to show you.

Not to bum out the op further, but this is one of the reasons i decided on going with icon coilovers instead of fox. We have tested them on many aftermarket brands coilovers on ebay, so you can purchase them in confidence. It actually sits 3/8 lower than the ome 881 that i just pulled off the truck.

You can put the small end of the allen in the collar or the long end depending on if you want to raise or lower the collar and use the rachet with the deep socket for leverage and stability. Let that stuff soak in. This does not hurt the coilover or the allen wrench (unlike the spanner wrench).

1320 performance coilover adjustment tool 4x steel spanner wrench. Icon's ave the ability to adjust the spring preload while on the vehicle with their spanner wrench. Free returns are available for the shipping address you chose.

So here are the numbers i came up with. The adjustable spring seat/nut is on top of the spring so it's accessible through the wheel well, above the tire, behind the uca. So i installed the passengers side 2.5 camburg coilover on the truck today.

For vehicles without an adjustable lower mount, use the spring perch to adjust ride height. I adjust mine by jacking the car up and holding the sleeve in one hand while turning the spring mount with the other hand. This is the ultimate wrench.

New double slatwall for displaying product. No tools to