How To Upholster A Bench Lid

Details of storage bench plan here youtube. Reassemble the hinges, lid mechanism, and the feet, adding the screws back to where they should go.

Borba Upholstered Storage Bench Upholstered storage

One of the most common questions i get is, “how do i upholster a bench?” i always practically scream, “it is soooo easy!!” i have helped dozens of people with this task.

How to upholster a bench lid. The problem with the way i covered the bench seat is that there is a lot of material in each corner that covers the original holes. And that’s how to upholster a storage bench. Build the bottom box of this small bench with storage using 2x4s and 2x8s boards.

Measure to find the center of the newly upholstered lid. If you are a beginner, watch the videos to see what works for your project. How to reupholster a storage ottoman.

Place your fabric right side down with the cushion and wooden base on top. The top of the chest is two pieces, the padded seat and the wood top. I lined up the edge of the fabric (wrong side up) with the front edge of the lid and then stapled all along the edge.

I began by removing all of the hardware and screws. So, i just sort of lined the seat up. Make sure to account for the foam.

The top is padded with foam for seating comfort, and opens to reveal ample storage space for extra blankets and linens. Decide how much fabric is needed to cover the top. Use a piece of plywood to build the evenly flat top lid of the bench that will be your seat too.

Select a fabric that is sturdy and beautiful. When autocomplete results are available use up and down arrows to review and enter to select. I did it this way so i would have a nice clean edge on the front lip of the lid.

Then i flipped the fabric over and brought it underneath the lid. Remove the old upholstery from the bench by finding the screws and unscrewing them. Staple the batting around the frame.

Lay the fabric over the foam and batting, and staple to the underside of the trunk using the staple gun. The base or the part that the fabric is attached to is not made of real wood. The top of the ottoman is the easiest part.

Screw the hinge into the lid. Align the center marks of the lid and the piano hinge. Silvertone nailhead trim and grid stitching lend a modern look, while button tufting and turned feet add a refined elegance.

It will make installing the hinges again a lot easier. Place the bench lid on top of the foam and trace the lid with a marker. Where the fabric ends, i just created an overlap and folded.

Remove the fabric seat top from the lane cedar chest. How to give an upholstered storage bench a new look. Hold the lid into place, align the center marks of the hinge and furring strip, and screw the hinge into place using the marked holes.

(no need to measure, just fold it up to determine what you’ll need.) allow a couple inches of excess fabric so you can fold it over before stapling it down. Also, upholster the plywood seat using leather and foam and enjoy a diy bench seat with hidden storage under the seat. I used foam that was 1 ½ inches thick.

The final step to reupholster a bench is to attach your newly covered bench seat to the frame. Cut the foam with your scissors. The first thing to do is examine how it was put together and find a good starting place to strip it down.

Follow that with the outer fabric. The lining was in great shape so i saved it. Feel with your hands and locate the screw holes for the lid mechanism.

Cut your batting 3 inches wider than the bench lid. Poke through the holes with an awl, then mark each hole with an x with your chalk. If you are reupholstering an existing bench, you will need to unscrew the legs and reattach them later.

Step 1, choose to either reupholster an existing bench or make a new one. Cut the foam and batting to size and lay it on the top of the trunk lid. Trim all the fabric sticking up.

Apply molding to the bench, if. I used a drill to remove the 8 screws holding the padded seat to the top. Staple opposite sides rather than around (that is, do the right side and then the left, rather than right, bottom, left, top), pulling as you go.

Being cautious not to pull too hard, begin stapling the fabric and batting to the wood so that it is taut across the lid. The thickness of the foam is your preference. Touch device users, explore by touch or with swipe.

I used 1 ½ inch foam because it was what i had on hand. Put one staple on one side, pull the fabric taut, then put one staple on the opposite side. Mark where the hinges need to be as well.

Measure and cut the new fabric to fit the bench. It is not a bad idea to mark them on your fabric with a fabric marker;

House of Hampton Ilchester Upholstered Flip Top Storage